The DeWalt 3D flashlight is the largest flashlight in DeWalt’s recently introduced line-up of LED lights. The DeWalt line of LED flashlights are heavy duty aluminum torches designed for outdoor, construction, and industrial use.
I found this flashlight is rugged, inexpensive, and bright, and that works as advertised. While I have no doubt it makes an excellent construction light, I found it did very well in a law enforcement and home defense capacity.
The DeWalt 3D is bright. Using common D-cell batteries, the DeWalt flashlight throws a bright 131 lumens. And since D-cell batteries are both inexpensive and available at virtually any store, you should alway be able to keep this light running without hurting the wallet. Also, D-cell batteries are normally stored by people for emergency preparedness situations, so it may share a common power source with other items such as radios in your preparedness gear.
The D-cells are obviously heavy, which means it is less easy to carry for long times as compared to lighter flashlights, but they also give the flashlight the heft needed to use it as an improvised impact weapon if needed. For someone keeping the light near the bedside for any nighttime intruders, having a heavy flashlight for close encounters may be appealing.
The DeWalt 3D compared to the Mag Charger flashlight.
As many of you know, I am a full-time police officer with a Florida department. I carried the 3D flashlight on-duty for several weeks, and was very pleased with its performance. I found the DeWalt 3D to be brighter than the department issued MagCharger flashlights, the long-time standard flashlight in police work.
The DeWalt 3D had a tight focused beam in the center, with a large circle of light that gave very good illumination over a wide area. The CREE brand LED is bright, efficient, and throws a pleasent white light, rather than the yellow light associated with incandescent bulbs.
Using regular Duracell alkaline batteries, the flashlight remained very bright over the course of three weeks of use, with little loss of brightness. I would imagine that someone using the light around the house or as a night-stand light would get many months of use out of this light before changing the batteries would be required.
I carried the 3D in a standard D-ring flashlight ring. When in the patrol car, I would jam the light between my gear bag and seat, or sometimes down between the driver’s seat and transmission hump. The black anodized aluminum body did not show any signs of wear from the ring or from use during the weeks I had the light. Frankly, the finish on the DeWalt flashlight held up better than most other flashlights I have used.
A scalloped head allows the user to immediately tell if the flashlight was left on, preventing the needless drain of batteries.
But, the finish is not the only thing tough about the DeWalt. All of the DeWalt LED flashlights were put through a variety of torture tests including a 25′ drop test, freeze test, 36 hour corrosion test, a 45 minute tumble test, and independant testing for light output by Lighting Sciences, Inc.
The grip on the 3D flashlight has a very pronounced texture which allows the holder to obtain a very secure grip on the light. The light has a hex-shaped head, so it will not roll away if set down, and it will not go far if dropped. I like the texture, and think it does a much better job than the less pronounced texturing on many other lights.
The DeWalt 3D flashlight is backed by a three year limited warranty and a 90-day money back guarantee. MSRP is a reasonable $79.99, but the DeWalt 3D flashlight can be had for only $59.76 at Amazon.com. If you need a full-sized flashlight for construction site, home projects, or even police or security work, the DeWalt 3D is a dependable, bright light at an attractive price.
Other articles that will amaze you:
I agree that the Mag charger light leaves a little to be desired as far as brightness. I will have to take a closer look at this Dewalt light for my line of work also.
Your review of the DeWalt 3D LED flashlight is best I have seen. I have been burned by rechargeable items so am especially interested in heavy duty lights using standard batteries.
Unfortunately, over many years I have developed the habit of storing my old police flashlight, which has a large reflector, upright or vertical on a shelf. This is not possible with the DeWalt. And your review completely omits to mention whether the DeWalt has a tailcap ring for hanging which is the only other storage method I’ve used. Even the manufacturer failed to say if there is a ring. No one has said if there is even a hole provided for a lanyard!
So can you tell me–Is a ring for hanging something I’m going to have to machine into the DeWalt 3-D flashlight myself?
And one other question: Is the current DeWalt being phased out next year for a design eliminating that great hexagonal anti-roll head?
Thanks for the feedback. I wrote that review more than two years ago, and I still really light the flashlight.
I don’t know if DeWalt updated the design, but my 3D can be store vertically on the head or tailcap with no problems. There are no holes or other ways of attaching a lanyard or loop to the tailcap. Someone handy with a drillpress should be able to add one easily though. As far as DeWalt phasing out the anti-roll head, I just don’t know. I’ve not seen any press releases on it, but that doesn’t mean they haven’t made that decision.
Thanks again for the feedback.
-Richard