Springfield SA-35 Review: Not Your Daddy’s Hi-Power

Last week, Springfield Armory announced its new SA-35 pistol. Like the company’s 1911 handguns, this iconic design is a modern riff on a highly-regarded John M. Browning design.

review of the Springfield Armory SA-35 9mm pistol

I love history and historic guns, so this one was right up my alley. I wanted to see how close the SA-35 compared to the Hi-Power. Also of interest to me was how Springfield would address some of the long-time (dare I say) flaws of the original.

So, I got my hands on a Springfield SA-35 and headed to the range to see how it shot. This is my review of the pistol.

As a side note, I recommend Will Dabbs’s full history of the Browning Hi-Power at The Armory Life. Be sure to come back and see how the new SA-35 compares.

Where to buy the Springfield SA-35

Where to Buy the Springfield SA-35

At the time of this writing, SA-35 pistols are selling for 2-3x suggested retail due to demand. I’m not surprised.

I recommend trying to catch one through our affiliate links:

General SA-35 Information

Springfield Armory designed the new SA-35 to be a modern iteration of the Browning Hi-Power: a pistol that maintains the look and feel of the original while taking advantage of modern manufacturing and needs.

testing the SA-35

Fundamentally, this is a single-action-only, hammer-fired pistol chambered for the 9mm cartridge. Browning originally designed the pistol for defensive use, and Springfield maintains that capability in the SA-35.

Here are some of the highlights of the SA-35:

  • forged steel slide and frame with CNC machining
  • improved tolerances while maintaining compatibility with many of the original parts
  • improved heat treating for additional strength
  • cold hammer forged barrel
improved SA-35 feed ramp
  • improved feed ramp geometry for improved feeding with modern hollowpoint ammo
  • modern sights
  • improved and extended thumb safety
improved thumb safety
  • deletion of the magazine disconnect safety
  • updated extractor for improved reliability
  • ring hammer with improvements to reduce hammer bite
ring-style hammer
  • flush-fitting 15-round magazines and compatibility with original 13-round magazines
  • bevelled mag well
  • compatibility with existing Hi-Power grips
  • Made in the USA

Let’s take a look at some of these features in greater detail.

Forged Steel

Springfield Armory has been very particular about identifying the slide and frame steel as forged and not cast. This is noteworthy because forged steel tends to be significantly stronger than cast in both tensile strength and fatigue strength. For a gun, this is important.

forged steel slide

While I am not a Hi-Power historian, it is my understanding that all Browning manufactured Hi-Powers used a forged frame until the company introduced the .40 S&W version. At that point, the company moved the entire line to cast frames.

cold hammer forged 9mm barrel in SA-35

I’ve not been able to get an official word on the recently announced Girsan MC P35. The only information released by the company is that the MC P35 has a “steel frame and slide.” I’ve been told that Girsan uses cast steel for at least some of its 1911 pistols, so my expectation is that its Turkish-made Hi-Power clone does as well.

My experience with the Girsan MC1911 CT was generally positive, even though the company opted for a cheap Chinese red dot that broke within the first 50 rounds of shooting.

Magazines and Capacity

Standard SA-35 magazines hold 15 rounds. This capacity is two more than original Hi-Power magazines. Yet, Springfield accomplished this in the same exact size as the 13-round Hi-Power mags.

SA-35 15 round magazines

So, if you were wondering if the SA-35 would take original Hi-Power magazines, the answer is yes. Likewise, you should be able to use the new 15-round Springfield SA-35 magazines in older Hi-Power pistols.

The FEG PJK-9HP pistols were a clone of the Hi-Power and used compatible mags. They should work fine in the SA-35 assuming they are still in-spec (a lot of the ones I’ve seen are pretty beat up.)

SA-35 Trigger

Like all other traditional Hi-Power pistols, the SA-35 is a single-action (SA) gun. Normally, SA guns have light, crisp triggers. However, the original Hi-Power pistols suffered somewhat due to a magazine disconnect.

trigger pull on Springfield SA-35 pistol

A magazine disconnect is a safety feature included in some pistols that prevents a gun from firing if the mag is not seated. While this feature is debated in its usefulness, most people acknowledge it negatively affected the quality of the Hi-Power trigger.

Springfield Armory tossed the magazine disconnect and re-designed the trigger system for the modern shooter. The result is a smooth pull with a crisp break. The company states the factory trigger pull should be around 5.5 pounds.

SA-35 trigger

With a Lyman digital trigger pull scale, I measured the SA-35 trigger pull weight slightly less than 5.7 pounds (an average of 10 pulls.) That’s pretty darn close to the company’s estimate.

The SA-35 trigger has a small amount of take up with a very short pull. As I said above, the break is very crisp. It feels as good as any other high-quality factory trigger I’ve tried in recent years.

best Hi-Power trigger

Reset is a touch long and not as pronounced as you might expect if you are used to shooting a modern striker-fired pistol. I could feel the reset when slow-firing, so it’s not as if it is non-existent.


This is one of my favorite aspects of the new SA-35 pistol.

The grips are finely checkered walnut. As with the original Hi-Power, the stocks are a two-piece design and are screwed into place.

walnut grips on the SA-35

Are SA-35 grips compatible with all other Hi-Power grip panels? Yes.

According to one company rep I spoke with, Springfield intentionally designed the grip panels to interchange with existing Hi-Power pistols. The idea is that any existing third-party grips will mount directly to the Springfield SA-35 without modification.

best Hi-Power wood grip

Of course, I love the stock grips. The wood feels perfect in the hand and looks great on the handgun.

The checkering is smooth when lightly moving your hand across them, but they really dig in and provide excellent traction during shooting. I can’t imagine a better set of factory grips on this pistol.


Another tip of the design hat to the modern world is found in the sights.

In your mind, roll back to the 1920s and 30s when the first Hi-Power/P-35 pistols were being designed. Pistol sights were a seeming afterthought in many designs.

SA-35 rear sight

Even in the modern era, the Hi-Power pistols often were equipped with sub-standard sights. You would often see a thin front blade that was hard to see, yet somehow provided enough glare to make shooting in bright conditions difficult.

Springfield opted to go a different route.

SA-35 front sight

On the SA-35, the company uses a matte black front post with a white dot. While still relatively thin, the front sight feels larger than many of the OEM Hi-Power sights I have seen.

In back, Springfield uses what they call a “Tactical Rack” rear sight. It is a plain black U-notch with serrations to eliminate glare. The leading edge of the sight offers a hook-like profile to enhance your ability to manipulate the slide one-handed.

rear tactical rack sight
You can see the rear sight’s leading edge can be used to rack the slide on a hard surface, belt or boot in an emergency.

These sights are a significant upgrade to typical Hi-Power sights while still maintaining the iconic look of Browning’s design.

Nevertheless, I hoped for a second option. While the included sights were fine in my shooting tests (read below,) I think I would have been better served with the U-Dot sights found on the company’s Hellcat pistol.

The U-Dot sights offer a much brighter front sight across all lighting conditions – something I am very interested in for any self-defense firearm, even the SA-35.

Hellcat Front Sight
This is the OEM front sight on my Hellcat pistol. I would have liked this as an option on the SA-35.

Now, you may see the SA-35 as only a fun shooter or as a collector’s piece. That’s fine. But, I see the Hi-Power platform as a viable personal protection tool. For that purpose, I think the Hellcat sights would have been a great option.

SA-35 Specifications

Here are the specs on the Springfield SA-35:

Barrel Length4.7″
Overall Length7.8″
Weight31.5 oz (with unloaded magazine)
Capacity15+1 (one magazine included)
Sightswhite dot front, Tactical Rack rear
Gripscheckered walnut

Range Testing

I was eager to get the SA-35 out on the range for testing. Knowing what 100+ years of shooting and manufacturing experience did for the 1911 platform, I wanted to know what more than 80 years might do for the “other” Browning platform.

Testing the SA-35 at the range

There were a few specific things I wanted to test while at the range:

  • reliability with hollow point ammo,
  • the quality of the trigger, and
  • if they fixed the infamous hammer bite.

Overall, the gun performed exceptionally well, though it missed my expectations by a whisker on the hammer bite issue. Read on for my experiences…

Ammunition Performance

Here’s a look at the ammo I tested in the Springfield SA-35. I selected a variety of loads including standard and high-pressure loads plus ball and hollowpoint.

I wanted to know if the gun would run every kind of ammo or if there would be issues.

American Eagle 115 gr FMJ1,188 fps360 ft-lbs
Federal HST 124 gr JHP +P1,219 fps409 ft-lbs
Federal HST 147 gr JHP1,036 fps350 ft-lbs
L-Tech 124 gr CuHP1,095 fps330 ft-lbs
Liberty Ammunition Civil Defense 50 gr JHP +P2,143 fps510 ft-lbs
PMC Bronze 115 gr FMJ1,147 fps336 ft-lbs
Sellier & Bellot 115 gr JHP1,197 fps366 ft-lbs
SIG SAUER V-Crown 115 gr JHP1,232 fps388 ft-lbs
SIG SAUER V-Crown 147 gr JHP1,039 fps352 ft-lbs
Speer Gold Dot 124 gr JHP1,146 fps362 ft-lbs
Speer Gold Dot 147 gr JHP1,022 fps341 ft-lbs
Wilson Combat 115 gr TAC-XP +P1,120 fps320 ft-lbs
Wilson Combat 124 gr GDHP +P1,136 fps355 ft-lbs
All loads were measured with a ProChrono Chronograph set at a distance of 15′ from the muzzle of the pistol. All measurements are an average of 5 shots from the SA-35.

I experienced no malfunctions of any kind. Considering I shot everything from the ultra-fast, lightweight Liberty Ammunition to more traditional projectiles weighing nearly 3x as much, that’s an impressive feat.

maximum recoil of the SA-35 when fired

Hollowpoints offered no issues at all for the SA-35. Every round fed, fired and ejected as I would expect.: no break-in time needed. Try that with a NOS Hi-Power from the 1930s.

So, reliability was a big win for Springfield.

Trigger and Accuracy

I described the trigger feel earlier in the article, but let me repeat the important part: it is light with a crisp break. On the range, it felt exceptionally good.

shooting low left
You can see on this target my low, left group from 7 yards.

While the trigger pull is just part of the overall shooting process, it has a major impact on accuracy.

All of the loads made sub-2″ groups at 7 yards using my backpack as an improvised rest. Some were around an inch. Without any rest, I still managed around 2″ or less – even with my increasingly arthritic hands.

So, the accuracy is very good in this gun. However, I suffer from stubby finger syndrome. While I consider my hands to be in the medium range, my gloves tend to be sized as large. Nevertheless, I have relatively short fingers.

Accuracy Testing of SA-35.jpg
In the article, I explain my low left groups. I adjusted my grip somewhat on this one to bring it closer to point of aim.

Consequently, traditional hammer-fired pistols like the Beretta 92, SIG P226 and Smith & Wesson 3rd Gen often require me to twist my hand slightly to get the proper amount of finger on the trigger shoe. Often, this causes my shots to go low left.

I experienced the same problem with the SA-35. It isn’t the gun’s fault. I just have the hands God gave me and I have to work with them as best I can. So, many of my shots were low, left.

Chronograph Testing
In my initial chronograph measurements, I shot just shy of 100 rounds. You can see how I consistently hit low, left.

A friend at the range had no such issues and ate the center of a bullseye with the gun at 7 yards.

So, I consider this another win for Springfield – assuming you don’t have stubby fingers.

Hammer Bite or Sharp Corners?

As with early 1911 pistols, some people have problems with hammer bite from the original Hi-Power designs. This is something that Springfield Armory set out to correct.

hammer bite on SA-35
As you can see, the SA-35 hammer is less likely to hit the web of your hand.

What is hammer bite? Hammer bite is a problem where the hammer of a pistol comes back far enough to hit the top of the hand holding the pistol. Hammer bite can cause minor discomfort or even injury including abrasions and bleeding.

Many original Hi-Power pistols used a spur hammer which seems to be the more frequent biter. Other Hi-Power pistols use a ring-shaped hammer.

Hammer Bite Testing
When shooting, I had very minor hammer bite with the SA-35. It’s significantly better than the original Hi-Power.

Springfield Armory opted for a ring-type hammer with slight changes to decrease the problems of hammer bite.

Nevertheless, I still had the SA-35 hammer brush the web of my hand. It wasn’t true bite, but it was close enough to suggest that others might have a problem. For me, the friction resulted in a small amount of redness and a sensation similar to an itch. It didn’t hurt, and I suffered no injury.

My friend who also shot the SA-35 didn’t have bite issues. However, he found some discomfort in the edges of the short beavertail. It seems that the corners on the side of the beavertail tend to dig into the web of his shooting hand. Perhaps Springfield can bevel the edges of the beavertail in the next version.

How to Clean the SA-35

While the shooting is the fun part, cleaning the SA-35 is an important aspect of ownership. Fortunately, field stripping the pistol isn’t as hard as you might think.

Field Strip the SA-35 for Cleaning

Here’s the process for field stripping and cleaning the SA-35:

Step 1 – Ensure the Gun is Unloaded.

Remove the magazine and lock the slide open. Visually check the chamber to make sure no cartridge is in the gun. Use your pinky to physically ensure nothing is in the chamber.

Too many people are injured or killed by guns that people thought were unloaded. It is your responsibility to make sure the SA-35 is truly unloaded and safe to clean.

Step 2 – Lock the Slide to the Rear
Take Down Notch on SA-35 pistol
As you can see, the takedown notch is sized identically to the safety notch.

Pull the slide all the way to the rear and push the safety – not the slide stop – up into the takedown notch.

Slide Locked Back for Field Stripping
Here you can see the safety engaging the take down notch.
Step 3 – Remove the Slide Stop

With the slide locked to the rear by the safety, the tension on the slide stop lever has been removed. It should wiggle easily.

Slide Stop Lever Push
From the right side of the frame, push the slide stop out.

Press the take down lever out of the SA-35 frame by pressing it from the right side of the gun. You can also grab the edges of the lever on the left side and pull/wiggle it out. It should come out relatively easily. 

Removing the Slide Stop Lever
The slide stop should be loose enough to pull out of the frame.

If the slide stop lever doesn’t wiggle or come out easily, check that you’ve locked the slide to the rear using the safety and not the lever itself.

Removing the Slide Stop from the SA-35 frame
Step 4 – Carefully Remove the Slide

Once the slide lever is out of the gun, the slide will come off of the rails. However, it is still under tension – so be careful with this step!

Slide Removed from the Frame

With a firm grasp on the slide, push the slide to the rear and disengage the safety. You can then slide the entire SA-35 upper assembly off of the frame.

Step 5 – Remove Guide Rod, Spring and Barrel

Once the slide is removed from the frame, turn the slide upside down so that the sights are facing down.

Spring and Guide Rod in SA-35

At this point, you can push the guide rod forward and out of the barrel’s notch. The rod and spring will lift out. You can then lift the barrel out of the slide.

Step 6 – Clean with Your Favorite Solvents and Oils

Clean the pistol using normal cleaning techniques. 

Cleaning Kit for the Springfield SA-35 pistol
You don’t need any fancy gear for cleaning the SA-35. A standard Hoppe’s pistol cleaning kit will get the job done.
Step 7 – SA-35 Reassembly

To reassemble the SA-35, you simply reverse the steps.

Proper Guide Rod Positioning in Springfield SA-35

However, you want to be careful when inserting the guide rod and spring into the slide: align the hole in the guide rod down. This will ensure the slide stop will slide back into place after you put the slide back on the frame.

Final Thoughts

The Springfield SA-35 is an amazing gun. The aesthetics are excellent as is the reliability and functioning of the 9mm pistol.

Keep in mind that this is not a true Hi-Power clone. While the looks are very similar and many parts are interchangeable, the SA-35 benefits from nearly a century’s progress in metallurgy, machining and manufacturing experience.

evaluating the Springfield Armory SA-35

Springfield Armory makes a big deal about not calling the gun a “classic.” The company wants the SA-35 to stand on its own, but I believe this gun is destined to become a classic in its own right.

If you can find one, I recommend buying it. The suggested retail price of $699 is a steal for a gun of this quality.

At the time of this writing, the guns are in full production, but demand far exceeds supply. Consequently, they are selling for 2x-3x the MSRP on places like GunBroker.

purchasing a SA-35

Purchasing the SA-35

As I mentioned earlier in the article, SA-35 pistols are very difficult to find due to heavy demand. I hope this will moderate.

Until then, I suggest trying to grab one through our affiliate links:

Last Update: 4/25/2022


As with all of my reviews, I provide a full disclosure so you are aware of potential biases that may impact what I’ve written.

First, Springfield Armory is not a sponsor or advertiser of GunsHolstersAndGear. In fact, I do not accept advertising from anyone at the time I wrote this article.

Second, the SA-35 was loaned to me by Springfield with every expectation that it be returned. As I really like the gun, I’ve contacted the company about buying it from them.

Third, while there is no direct influence from Springfield Armory on any aspect of this review, I provide contract work for SEO and editing work on The company doesn’t tell me what to do or write on my own sites, and I provide my honest opinions on all guns – including theirs. However, it is a potential bias you need to know about.

Lastly, GunsHolstersAndGear is a family-owned business. I earn money through the use of affiliate links to places like Palmetto State Armory, Amazon and Optics Planet. If you use one of these links to purchase something, I earn a small commission.

Please leave your thoughts on the SA-35 or my review in the comments section below. I only ask that you keep the comments civil and profanity-free as this is a family site.

Thanks for reading and your continued support!

By Richard Johnson

Richard Johnson is a gun writer, amateur historian and - most importantly - a dad. He's done a lot of silly things in his life, but quitting police work to follow his passion of writing about guns was one of the smartest things he ever did. He founded this site and continues to manage its operation.

13 replies on “Springfield SA-35 Review: Not Your Daddy’s Hi-Power”

Good article. I hope that SA will produce a 10+1 round version, with an ambi safety, for obvious reasons.

Welp, here it is.

This was inevitable to happen, and I’m glad Springfield took the lead in bringing back this classic Classic.

No other handgun in all of gundom appeals to me more than the Browning High Power / MP-35. The sleek lines, hand feel ergonomics, accuracy, reliability is truly in a self defined class of it’s own.

I own an early 90s MkIII, and I’ve requested it to be buried with me when I meet trails end.

Mine has always been reliable with the old style Federal 9BP loads, and other than feeding it ball rounds, nothing else has ever been fired in it.

This gun is totally reliable and very predictable to me, its never offered surprises other than ongoing amazement. If ever you wanted to own a HP, now is your chance. Although its not a Browning, the SA-35 appears to be a more refined version of it’s original incarnate.

Once the price drops to MSRP, or lower, I’m sure ill pick one up.

Great looking pistol. I just had the local gun store put one on hold. Is the barrel a one-piece barrel (unlike the original which is a two-poece barrel)?

Comments are closed.